ANTI-GRAVITY PROJECT by Jeff Lucas Astrophotographer : Published on Oct 26, 2018

Some YouTube notes on Lenz's, Ohm's Law and Nikola Tesla about how Jeff Lucas thinks anti-gravity works.


Some YouTube notes on Lenz's, Ohm's Law and Nikola Tesla about how I think anti-gravity works. When it comes to building anti-gravity, everyone is building it wrong, its upside down, its not the number of magnets, it how much E = I/R ~ direct current you can apply to magnets to create levitation repulsive force, polarities e.g. North to North, South to South.

We're not applying direct current to magnets to increase its polarity and we're not inducing spin against reflective metals. I believe if we can apply a strong surge of direct current like a rail gun power to magnets using series circuit north to south (top to bottom) and induce high spin with R/C 10K rpm motors to spin magnets and reflect / deflect the increased magnetic repulsive field from top thin plate of copper / aluminum sheet downwards, anti-gravity; it should work. If I want this to work without being tethered as seen here, I will need 1.21 gigawatts of power but, as you know this would be a larger scale Marty. I will be making a small type Hover Board scaled height 4", width 10"..

Can you connect the dots?
1:47 Its not how many magnets but how much direct current applied.
2:22 Lenz's Law in motion
3:08 Aluminum makes great sail for magnetic flux, see later in video.
4:12 Halbach Array of Magnets
4:43 Halbach Array doesn't have applied direct current, imagine if applied.
5:51 Lenz's Law explained back in 2009 by iLevitation
6:24 Gravity Wave - wrong direction - need opposing polarities.
7:46 No need for mercury unless you have 1.21 gigawatts for direct current.
9:18 Anti-Gravity demoed in house - notice aluminum plating and its pitted for reason.
10:03 Anti-Gravity demoed outside backyard -notice aluminum plating and its pitted for some reason ~ Hint: purple beetle inner wings.

10:22 Bob Lazar, "How would you describe gravity?"

For this project I will need two R/C 10K RPM drives @ 12volts, no bigger than your 9 volt battery. Next fabricate a conductive six point star hub to hold six neodymium 115 lbs lifting magnets, rare Earth magnets staggered North, South, North, South, North, South, radius x/y axis of each arm magnet will be 2 inches away from center hub for 4 inch diameter rotation to create repulsive force upwards and outwards lift beneath 5 to 7 inch copper array..

Create mounts for two 10K RPM drives with copper shaft to spin six star magnet hub. First 10K drive will sit below stationary copper array, 2nd 10K RPM drive is for top rotating copper disk, to counter rotate bottom rotating magnets for stability, negating yaw. The 2nd rotating copper disk may contribute to increasing magnetic repulsion. Rotating disk and stationary will have a few holes so electrons can pass upwards, the spacing of the copper plating may result in a Biefeld-Brown Effect, my goals is to energize the magnetic fields, not move ionized air, however it may so. Copper shaft will conduct DC power like a trolley electric car or like your electric train set, Powered by direct current, 7:46 positive lead will be connected to top shaft, negative terminal to bottom shaft to complete series circuit. DC voltage will be used to energize, increase magnetic field.

Next, I will carefully fabricate a flat pitted reflective magnetic flux array, from 99.9% pure copper cut metal sheet foil 0.1X7.9X19.7" cut into a circle, center hole punched for 10K rpm drive shaft for six magnet hub. The pitted copper array positioned 0.5 to 1 inch (varying magnetic field) above the rotating magnets polarities North South etc. for optimized repulsive force, you want it spaced where the magnetic field attracts to the copper array at its strongest point.

Next phase testing Halbach array 5:47 configuration for rotation.
Category
Science & Technology